Serving the Greater Toronto Area & beyondEnglish · हिंदी · ગુજરાતીFor Realtors →
(437) 227-6800WhatsAppcontact@jbminspect.ca
Moisture & hidden leak investigation

A water stain, a damp patch or a leak you can't trace?

A Focused Moisture Investigation looks at one defined concern, such as a ceiling stain under a bathroom, a wet window sill or a damp wall, using visual checks, thermal imaging and moisture-meter readings. You get a short report on what the evidence shows, how far it extends, the likely sources worth checking and who to call next.

Sound familiar?

Concerns this investigation is designed for

Ceilings

A stain on the ceiling

Under a bathroom, below an upstairs laundry, under the roof after snowmelt or heavy rain, or below an air conditioner or furnace in the attic.

Windows & walls

Water at a window or a wet wall

Damp drywall under a window, peeling paint, swollen trim or a wall that feels cool and soft, often after wind-driven rain.

Wet areas

Around tubs, showers and sinks

Loose tiles, failing caulking, stains on the ceiling or wall next to a shower, or damp cabinet floors under a sink.

After a repair

You want to know if it's dry now

A leak was fixed and you want readings of the accessible surfaces before closing up, repainting or listing the home.

Who this is for: homeowners, condo owners, landlords and property managers with a specific concern. For a basement, see our basement moisture page, which explains the different causes below grade. If you are buying a home, moisture checks are already part of our home buyer inspection.

How we approach it

How a focused moisture investigation works

  1. History first. When does it appear? After rain, with wind from one direction, after showers, after snowmelt or only in winter? The pattern of a leak often says more than a single reading.
  2. Look at the affected area and what is above or beside it. The bathroom, roof area, window, exterior wall or plumbing fixture most likely to be involved, where it is accessible.
  3. Thermal imaging to map patterns. Evaporating water cools a surface, so damp areas often show as cooler than their surroundings. The camera helps us see the shape and extent of a suspect area and choose where to take readings.
  4. Moisture-meter readings to check. A cool pattern is not proof of moisture: missing insulation, air leaks and cold pipes look similar. We take readings at suspect and comparison areas with pinless and pin-type moisture meters before drawing conclusions.
  5. Report and next step. What we observed, where readings were elevated and how consistent they were, the likely sources worth investigating and which trade to call, such as a plumber, roofer or window installer.
Thermal imaging

What thermal imaging can and cannot establish

It can help show
  • Surface areas with temperature patterns consistent with moisture, which we then check with a meter.
  • The approximate extent of a suspect area on a ceiling or wall, so readings and any later repair are better targeted.
  • Patterns that point toward a likely path, such as cooling that runs from a window corner or along a ceiling joist.
It cannot establish
  • That moisture is present from the image alone. Thermal findings need corroboration with a meter and visual evidence.
  • What is happening inside the wall or ceiling cavity, or the condition of framing behind the finish.
  • The source of a leak with certainty, or that a leak which was dry on the day has stopped.
  • Whether mould is present or what type it is.

How findings are reported

Each item in the report is labelled, so a cool area on a thermal image is never reported as a leak on its own.

In the reportWhat it meansExample (illustration, not a client finding)
ObservationWhat was seen, photographed or measured, with the conditions at the time.An irregular cool area on the ceiling below the bathroom.
Possible explanationWhat the observation is consistent with. Usually more than one explanation fits, and the report says which.Consistent with moisture from the shower or tub above; missing insulation or air movement could look similar.
Confirmed findingStated only when separate lines of evidence agree: for example, consistently elevated readings at several points, compared with readings on the same material in an unaffected area, together with a matching thermal pattern or visible staining. A single elevated reading is reported as an observation, not as proof of moisture. A source is confirmed only if it is directly visible.Readings stay elevated across the cool area with both pinless and pin-type meters, readings on the same ceiling away from it are normal, and the area matches a visible stain. Together these support a finding that the ceiling surface is damp. The source is not confirmed unless visible; a plumber is recommended.
Conditions & limitations

What can limit the results

  • Many leaks are intermittent. A roof or window leak that only appears with wind-driven rain may be dry on the day of the visit. If you can, book soon after it shows, and keep photos and dates of when it appears.
  • Meters have limits. A pinless meter scans a surface without marking it; a pin-type meter, which leaves two tiny holes, gives a reading at a specific spot. Both give readings that depend on the material and how deep they read, and metal behind the surface, foil-faced materials, and dense or salt-contaminated surfaces can raise a reading without water being present. That is why one elevated reading is never treated as proof on its own. Meters also cannot reach every concealed layer, and a normal reading at the surface does not prove a cavity is dry.
  • Non-invasive only. Apart from the tiny holes a pin-type meter may leave, we do not open finishes, cut inspection holes, remove tiles, run water tests or take laboratory samples. Where opening a surface is the only way to confirm a concern, we say so and recommend the right trade.
  • One defined concern. The service covers one concern or one connected affected area, with up to 75 minutes on site. If more time is needed, we ask for your approval before continuing.
  • Mould. We describe visible staining or suspected growth and where moisture readings are elevated. We do not test for or identify mould, or provide mould clearance. Health Canada's guide to moisture and mould explains why fixing the moisture source comes first.
What you receive & price

Focused Moisture Investigation: $279 + HST

A focused diagnostic service. It does not include a complete home inspection.

This is the moisture option of our Single-Concern Assessment: one localized concern, agreed before booking, at one price for any property type.

  • Up to 75 minutes on site for the one concern agreed before booking.
  • Visual assessment of the accessible affected area.
  • Thermal imaging and moisture-meter readings where appropriate.
  • Photographs and a concise written findings report, within two business days.
  • Recommended next steps, including specialist referral where needed.
ServicePrice
Focused Moisture Investigation — a Single-Concern Assessment (any property type)$279
Additional investigation, only with your approval$125 per hour, in 30-minute increments
Combined Thermal & Moisture Assessment (winter thermal survey plus one moisture concern)$399 condo · $449 town/semi · $499 detached

Plus 13% HST. Any additional reporting fee is agreed in advance. Travel adjustments may apply and are confirmed before you book.

In short: a JBM Inspect Focused Moisture Investigation is $279 + HST for one defined concern at any property type, with up to 75 minutes on site, thermal imaging and moisture-meter readings, and a written report within two business days. It is non-invasive screening: it does not open finishes, test for mould or guarantee that the source of a leak will be located.

Questions

Moisture and leak FAQ

Is this a Single-Concern Assessment?

Yes. Focused Moisture Investigation is the moisture option of our $279 + HST Single-Concern Assessment: one localized concern, up to 75 minutes on site, and a concise report within two business days. A whole-home survey or wider post-flood investigation needs a different agreed scope.

Can a thermal camera find a leak inside a wall?

Not on its own. A thermal camera shows surface temperatures. Damp materials often appear cooler, so the camera helps find areas worth checking, which we then test with a moisture meter. It cannot see inside the wall, and it cannot guarantee that the source of a leak will be located.

Will you find the exact source of my leak?

Sometimes the evidence clearly points to a source, and sometimes it narrows the options. We report what the evidence supports and recommend the trade best placed to confirm and repair it, such as a plumber or roofer. We cannot guarantee a source will be located, especially if the leak is not active on the day.

Do you test for mould?

No. We describe visible staining or suspected growth and where readings are elevated, and recommend a qualified professional if needed. Health Canada does not recommend routine air testing for mould; fixing the moisture source matters most.

Can I send photos first?

Yes. Photos of the stain and the area above or around it, and notes on when it appears, help us confirm whether this service fits before you book. Send them by WhatsApp or include a description in the quote form.

What if the investigation needs more than 75 minutes?

Additional investigation is $125 per hour, billed in 30-minute increments, and only with your approval before it starts.

Seeing a stain or a damp patch?

Send a photo and tell us when it appears. We'll confirm whether a focused moisture investigation fits, and your total price, before you book.

CallWhatsAppGet a Quote
Chat on WhatsApp