Buying an older Toronto house: wiring, basement and heat loss
What buyers of pre-war and mid-century Toronto homes worry about most, what official sources say about it, and what a home inspection with thermal imaging can and can't tell you.
Short answer: in an older Toronto house, a home inspection can report the visible condition of wiring, the basement, plumbing and insulation, and thermal imaging can show surface temperature patterns that point to moisture, missing insulation or air leaks. It cannot see inside walls, test water, or replace a licensed electrician's assessment or an energy evaluation. Where something needs more than a visual look, the report says who to call.
Older wiring
The Electrical Safety Authority (ESA) describes knob-and-tube as an older wiring method used in homes from the early 1900s to the 1940s and no longer installed. It lacks modern protections such as ground fault circuit interrupters (GFCIs) in wet areas. ESA says it can be considered safe when properly maintained by a Licensed Electrical Contractor, and that many insurers will not provide or renew coverage on a home with it, or may require it to be replaced first.
ESA's advice to buyers is to have a Licensed Electrical Contractor assess the wiring and to check with an insurer before buying. See ESA's page on knob-and-tube wiring.
During an inspection we look at what is visible and accessible, such as the panel, visible wiring in the basement and attic where reachable, ungrounded outlets and missing GFCI protection near water. Wiring inside finished walls cannot be seen. If we see signs of older or altered wiring, the report recommends an evaluation by a licensed electrician.
Basements and water
Older basements often have brick or stone foundations, parging that has aged, and finishing added over the years. We check for stains, efflorescence, musty areas, grading and drainage at the exterior, and use a moisture meter where something warrants a closer look, with thermal imaging where it helps. Our Signature package adds expanded moisture screening at accessible wet areas and basement risk locations.
A basement that is dry on the day of the inspection may still have leaked in the past, and one that shows a stain may be an old, resolved issue. That is why it is worth asking the seller about any past water entry and repairs. The City of Toronto's Basement Flooding Protection Subsidy Program describes subsidies for some home flood-protection work, with limits that change, so check the City for current details. If you already own the home and the basement is damp, see our basement moisture investigation.
Lead in water pipes
The City of Toronto says lead service pipes can be found in homes built before the mid-1950s, and that solder used before 1990 can contain lead. Testing is the only way to know whether water contains lead, and the City offers free testing. We note pipe materials we can see, but we do not test water. See the City's page on lead in drinking water.
Heat loss and drafts
Natural Resources Canada explains that heat moves in every direction, and that uncontrolled air movement through the building envelope can be a major source of heat loss. Its guide Keeping the Heat In lists common leak locations, including gaps around windows, doors and attic hatches, the rim joist and sill plates in the basement, and openings around plumbing, vents and wiring. It also lists insulating a poorly insulated attic and basement as typical retrofit opportunities.
NRCan says the best way to judge a home's improvement potential is a professional energy evaluation by a certified energy advisor, which includes measuring insulation and a blower-door test. That is a different service from a home inspection, and we do not provide EnerGuide evaluations.
Already living in an older house with a cold room or drafts? See what a winter thermal imaging survey can and can't show, or our page on cold rooms and uneven heating.
Where thermal imaging helps
Thermal imaging shows surface temperature patterns. In an older house it can help point to cold areas that suggest missing or settled insulation, draft paths around windows and attic hatches, patterns that suggest moisture, and unusually warm electrical connections. These are clues, confirmed where possible with other tools such as a moisture meter. Interior thermal results are strongest in the heating season, roughly October to April in the GTA, when there is a clear temperature difference between inside and outside. Read more in our guide to what thermal imaging can and can't show.
Thermal imaging is included in every JBM Inspect home inspection. Essential includes targeted imaging of areas of concern. Signature adds systematic room-by-room thermal screening where conditions support meaningful results.
What an inspection can't do
- It is visual and non-invasive. It cannot see inside walls, under finished floors or behind insulation.
- It does not test water, sample for mould or asbestos, scope sewers, or provide WETT reports, structural engineering or EnerGuide evaluations.
- It does not certify that work was permitted or meets code. If the report notes signs of unpermitted or poorly done work, it recommends a check of permits and an evaluation by the appropriate licensed trade.
Not every older home has every condition described here. The report covers what is visible on the day, ranks each finding as safety, repair or evaluate, monitor or maintain, and says who to call.
What it costs
Complete inspections start at $349 + HST for a condo, $399 for a townhouse or semi and $449 for a detached home with Essential, and $449, $499 and $549 with Signature. Homes built before 1950 carry a $75 adjustment because they take longer. See the instant estimate or read about home inspections in Toronto.
Common questions
Can a home inspector tell me if a house has knob-and-tube wiring?
Sometimes. We can identify it where it is visible and accessible, such as in a basement or attic. We cannot see wiring inside finished walls, so the report recommends an evaluation by a licensed electrician when there are signs of older wiring.
Does thermal imaging find leaks and missing insulation in an older home?
It can show surface temperature patterns that suggest moisture, missing insulation or air leaks. It does not see through walls, so findings are confirmed where possible with a moisture meter and described with their limits.
Is a home inspection the same as an energy audit?
No. An EnerGuide evaluation by a certified energy advisor includes insulation measurements and a blower-door test. A home inspection reports the visible condition of the home, and we do not provide EnerGuide evaluations.
Have an offer deadline?
Tell us your condition or warranty deadline and we'll confirm scope, availability and your total price before you book.